全国劳动热线:

18396804865 钱经理

美洲杯竞猜平台,美洲杯足彩竞猜,美洲杯竞猜官网

2019-12-21 16:27:00 文章来源:www.neyon.net 201

分立式美洲杯竞猜平台激光切割板才出去的人格优劣有各级地方原因,他根本缘故有以下内容1、板才放置不平静.必需时能够把板才加垫.

The quality of laser cutting board of portable NC cutting machine is good or bad because of various reasons. The key reasons are as follows: 1. The board is not stable until it is placed. It can be padded only when necessary.

2、割缝余量预留不足.尤其切割厚板时割缝余量至少在10mm上述.

2. The slot allowance is insufficient. Especially when cutting thick plates, the slot allowance is at least 10 mm.

3、上班条件光线不足.视觉观察不规范.尤其是晴到多云、夜间作业.

3. Insufficient light in the working environment, inaccurate visual observation, especially overcast and evening work.

4、切割中熄弧或未割穿,此刻对与厚板一定重新移至切割点以上2MM处再继续切割,若未移至准确位置即起弧可能会对零件边缘进一步融割出现缺陷.

4. Extinguishing arc or not cutting in cutting. At this time, the thick plate must be moved to 2MM above the cutting point to continue cutting. If not moved to the exact position, arcing may cause defects in further cutting the edge of the part.

5、切割行进方向应确保切割结束在周边板区.若结束在小面积板区会因受热板材移动导致切割变形.为此在切割厚板时可以正反方向各切割一段,会友处要适时熄火,避免切割过度致使零件缺损.

5. Cutting direction should ensure that the end of cutting is in large area. If the end is in small area, the cutting deformation will be caused by the movement of heated plate. For this reason, when cutting thick plate, the cutting section can be cut in both positive and negative directions, and the intersection should be extinguished in time to avoid excessive cutting resulting in part defects.

6、喷嘴,两极,喷嘴帽坚持每天检查,如有损坏及时更换.

6. Inspect nozzles, electrodes and nozzle caps every day and replace them in time if they are damaged.

7、划线要准确,留足割缝余量和板材边缘余量.

7. Marking should be accurate, leaving enough slot allowance and plate edge allowance.

8、厚板切割需加工的各路放到10MM-15MM.

8. The allowance for thick plate cutting should be placed at 10MM-15MM.

9、划线切割时板材摆放方向要结合零件排布、-X轴向切割来确定,追求便于观察.

9. The orientation of plate placement should be determined by combining the layout of parts and - X axial cutting, so as to facilitate observation.

10、造成切割尺寸误差的要素:伽马射线不规范、切割面倾斜、零件受热移动、一处多次重复起弧、划线不规范、试点、零点观察不规范等.

10. The factors causing the error of cutting dimension are inaccurate diagonal line, inclined cutting surface, parts moving by heat, repeated arcing in one place, inaccurate marking, inaccurate starting point, inaccurate zero observation, etc.

是的运用操作美洲杯竞猜平台能有效增长切割质量以及减少板材的浪费

Correct use of CNC cutting machine can effectively improve cutting quality and reduce waste of sheet metal http://neyon.net/

  报错


  美洲杯竞猜平台是大型美洲杯足彩竞猜厂家,数控美洲杯竞猜官网厂家,分立式美洲杯竞猜平台厂家www.neyon.net,供应河北美洲杯足彩竞猜,辽宁数控美洲杯竞猜官网,澳门便携式美洲杯竞猜平台,江西美洲杯足彩竞猜,广西数控美洲杯竞猜官网,江西美洲杯竞猜平台,陕西美洲杯竞猜平台,甘肃美洲杯竞猜平台,山东切割机,浙江切割机,安徽美洲杯竞猜平台,福建切割机,山西切割机,青海美洲杯竞猜平台,四川美洲杯竞猜平台,安徽切割机,海南美洲杯竞猜平台,云南美洲杯竞猜平台,吉林美洲杯竞猜平台,甘肃切割机,青海切割机,陕西美洲杯竞猜平台,蒙古美洲杯竞猜平台,要求的爱侣联系我们15254176866

  • 沟通电话

    18396804865
  • 微信扫一扫

  • 电话机咨询
    邮件咨询
    在线地图
    QQ客服
    血站地图